C/W: Rd Olson Mfg. tri-axle chassis, lights & air brakes, road legal, NEW 10:00 x 22.5 tires, 4- Dual cylinder 12 volt jacking legs, pump, tank, cable & controls, jaw 30 x 42, deep nip angle, won’t blow rocks out, 20” VGF with bolt in floor liner, hydraulic ship adjust, hydraulic locks, motor & controls, power cords.
Comments: New chassis safety, one new stationary jaw die, moveable at 50% and has been flipped, field ready, impact bed under jaw, bearings in oil, new Hardox AR450 on hopper walls, new 480 volt motors, all test ran, unit has gone through the shop.
Located in Leduc, AB
C/W: 2007 chassis & CAT C15 engine (2700 hrs) pre-emission, new 2025 400 Kw Generator on engine, new 2025 -100 HP motor & hydraulic pump, new electric panel (300 hp soft / 100 hp starter), new 2025 Minyu 45” cone, - 250 hp cone motor, hydraulic adjust & clearing, lube system complete, pump, tank heaters, cooler & fan, feed conveyor, variable speed, liner so not require any backing when changing, feed conveyor, variable speed, remote control tracks & feeder conveyor speed, high discharge under cone belt
Comments: Converted it into an electric cone (no clutch, jack shafts, or high maintenance drives), will reach to top of most screen decks, chassis was completely sand blasted a repainted in 2025, generator will run a screener & jaw on site, generator, cone, and switch gear are all band new, North American build track chassis
Located in Leduc, AB
C/W: 2005 chassis, refurbished 5 years ago, 2017 Minyu 300 high speed cone (no backing needed when changing liners), 36” In & out belts, power cords lube tank, heaters, pump, cooler & sensors, triaxle, 5th wheel pull, HPU for cone clearing & adjust (from the tower)
Comments: Cone came into the shop about 18 months ago, cleaned up, serviced, alignment pins, some accumulator work, cone inside was in extremely good condition, went back to customer, crushed 3 months, and has been sitting
Located In Leduc, AB
View Details:
About 500 Hours
C/W: Cat engine, track mounted, handheld Remote control, steel punch plate drum, 5/8” openings, hydraulic brush adjust, smart feeder (stops so drum does not stall or plug), 2 fold out product conveyor (rear is variable speed)
Comments: Swing our engine, feeder hydraulically slide out for servicing, lowest feed heigh in industry, no ramp needed, lowest fuel consumption in the industry (by thousands of dollars per month compared to its competitors)
Located in Leduc AB
Hours: 144(144 hrs.)
C/W: Cat diesel engine, fully self continued, bolt on hopper wings (transport on hitch), 1 x 30” x 40 conveyor, 1 x 36” x 40 conveyor, both run hydraulically off the unit
Produces 3 sized rock products from 4” up to 32”
Comments: Conveyors are from a 2025 Rip Rap, Customer did not take them, at 333 hrs, were repainted at 189 hrs, hitch folds up when working, produces 3 sized rock products from 4” up to 32”
Located in Leduc, AB
Hours: 2,137
C/W: 23-speed Powershift, 50Km, front & rear 3pt hitch, 6 rear & 1 front hydraulics, front & rear PTO, rear 3pt controls, heated/cooled seat with massage, LED lights, fully integrated GPS with StarFire 6000, 650/60R34 front & 900/60R42 rears, rear wheel weights.
Comments: AutoTrac Turn Automation, Basics, Data Sync, Data Sync Documentation, ISOBUS Documentation, Implement Guidance, In-Field Data Sharing, Machine Sync, Row Sense Guidance, Section Control, Tractor Implements Automation.
Financing options are available for this equipment. Visit here to apply and learn more.
Serial Number: 1RW8410DPNB220190
Hours: 1,892
C/W: 23 speed Powershift, 33mph/50km, front & cab suspension, front & rear 3pt hitch, 84gal/min hydraulic pump, 5 hydraulics, joystick, big 1000 PTO, rear controls, LED lights, AutoTrac Ready GPS, Gen 4 display, 650/60R34 front, 900/60R42 rear, rear wheel weights.
Comments: AutoTrac Guidance, Basics, Data Sync, ISOBUS Documentation, In-Field Data Sharing, RowSense, Section Control.
Financing options are available for this equipment. Visit here to apply and learn more.
Serial Number: 1RW9620RPHP804421
Hours: 6,664
C/W: 18 speed Powershift, 115G dual main hydraulic pump, 5 hydraulics, 30" Camso 6500 tracks, 3pt hitch, AutoTrac Activation.
Hours: 6,664
Financing options are available for this equipment. Visit here to apply and learn more.
Serial Number: 1NKDXPEX6DR961259
576,490 kms
C/W: 485 Paccar engine, 18 speed Easton automatic transmission, air ride, air suspension, air dump, air seat, full load cab, full lockers, 3 stage engine brake, 16,000# front axle 60,900# rear axles.
Comments: 4.10 ratio, new unused 25, AEM grain box w/ silage end gate, 66" sides, new nordic HD hoist and controls, in cab & rear hoist controls, new Michel's roll over tarp, new front tires, truck is a full maintenance fleet truck, very rare tri axle automatic grain truck.
Financing options are available for this equipment. Visit here to apply and learn more.
Serial Number: 1HTMMAAP86H343563
294,600 KMS
C/W: IHC DT 466 engine, Allison 3000 RDS automatic transmission, hydraulic brakes (class 5 to drive), air side seats, AC, tilt, cruise, 3.90 ratio, 10,000# front axle, 17,500# rear axle.
Comments: crew cab with lots of room, fancy custom made leather seats, custom made deck, aluminum toolbox, lots of chrome, very good 22.5 tires.
Financing options are available for this equipment. Visit here to apply and learn more.
Serial Number: 1FVACXCS75HV24874
303,123 kms
C/W: MB 210 HP engine, Allison 2500 RDS automatic transmission, air brakes, AC, cruise, heated mirrors, service box with lots of deck room, stabilizer feet, 10,000# front axle, 19,220# rear axle.
Comments: Hiab 077CL picker, lifts 5500 lbs, reaches 30 feet, lots of cab room for the crew or tools.
Financing options are available for this equipment. Visit here to apply and learn more.
Serial Number: 1FVPC5CV09HAE3846
681,000 kms
C/W: MBE 435 HP engine, Allison 4500 RDS automatic transmission, air brakes, air suspension, air seat, full lockers, variable engine brake, full load cab, 4.10 ratio, 20,000# front axle, 49,800# wide track rear Axles.
Comments: New front tires, near new rear tires, 5 compartment aluminum fuel tank, C/W pumps, hoses, reels nozzles gauges, etc, current CVIP, from a well maintained fleet, very hard to find Allison automatic tri axle truck.
Financing options are available for this equipment. Visit here to apply and learn more.
Serial Number: 1FVACXCS77HY55666
246,300 kms
C/W: MBE 230 HP engine pre emission, 6 speed smart shift automatic transmission, air brakes, air suspension, air dumps, air ride seat, AC, tilt, cruise, 4.63 ratio, 12,000# front axle, 21,000# rear axle, near new 22.5 tires.
Comments: 21' refurbished, blasted and painted roll back deck, with winch, side boom, rear wheel lift, dual side controls, new tool boxes, new PTO and pump, all new hydraulic hoses.
Financing options are available for this equipment. Visit here to apply and learn more.
Serial Number: ZDF138709
Hours: 4,952
Part of a Complete Dispersal for Lee Bates
C/W: Powershift, 6 hydraulic outlets, Big 1000 PTO, Trimble Case IH 372 receiver, AFS Pro 700, luxury cab package
Comments: stored inside, tracks are about 70%, farmer-owned east of Stettler, Alberta.
Financing options are available for this equipment. Visit here to apply and learn more.
Serial Number: THX14752
Part of a Complete Dispersal for Lee Bates
Hours: 11,145
C/W: C frame, tilt, manual side discharge, Allied W6G winch, 199" dozer, enclosed cab, 36" pads.
Comments: Dozer has been used on the farm by the current owner. Undercarriage has had recent updates, job-ready.
Financing options are available for this equipment. Visit here to apply and learn more.
Serial Number: 6054714
C/W: SELLS WITH 64,000 LITRES OF FUEL, double wall, fully welded saddle design, powder-coated, pump, Fill-Rite meter.
Comments: As new, diameter: 302 cm (119 in.), tank length: 1,077 cm (424 in.), overall length with skid: 1,326 cm (522 in.) weight: 13,594 kg (29,970 lbs.) with skid
Financing options are available for this equipment. Visit here to apply and learn more.
Hours: 500
C/W: Cat 7.1 ACERT Tier 4 Final Engine, Track Mounted Jaw Crusher, Wired Remote Control, Dust Suppression System, Dirt (Fines) Conveyor, Cross Belt Magnet, New Lower Cheek Plates Installed, Includes New Stationary Jaw Plate, Includes Additional New Lower Cheek Plates, Service Records Available, Factory Manuals Included
Comments: Well-maintained, low-hour jaw crusher equipped for aggregate production, recycling, and crushing applications. Recent wear component replacement includes new lower cheek plates, with a new stationary jaw plate and additional lower cheek plates included. Ready to continue working.
Financing options are available for this equipment. Visit here to apply and learn more.
Hours: 1,000
C/W: Cat 7.1 ACERT Tier 4 Final Engine, Track Mounted Impact Crusher, Wireless Remote Control, Dust Suppression System, Dirt (Fines) Conveyor, Cross Belt Magnet, Service Records Available, Factory Manuals Included
Comments: Well-equipped impact crusher suitable for aggregate production, recycling, and asphalt processing applications. Features dust suppression, fines conveyor, and cross belt magnet to maximize production efficiency and material separation.
Financing options are available for this equipment. Visit here to apply and learn more.
Hours: 560
C/W: Cat C2.2 Engine, Track Mounted Conveyor Stacker, Wired Remote Control, Service Records Available, Factory Manuals Included
Comments: Late-model stacker in excellent condition. Designed for efficient stockpiling and material handling in aggregate, sand, gravel, and recycling operations. Low-hour machine ready for immediate use.
Financing options are available for this equipment. Visit here to apply and learn more.
Hours: 500
C/W: Tier 4 Final Engine, Hydraulic Wedge Quick Coupler, 60" Cleanup Bucket, 42" Armored Digging Bucket, Cab Guarding, Auxiliary Hydraulics, Reduced Tail Swing Design, Service Records Available, Factory Manuals Included
Comments: Low-hour reduced tail swing excavator equipped with hydraulic quick coupler, cleanup bucket, armored digging bucket, and cab guarding. Ideal for civil construction, aggregate, utility, and general excavation work.
Financing options are available for this equipment. Visit here to apply and learn more.